Time to Shelve the Low End

STUDIO QUALITY

I’ve recently returned home from Sting’s Symphonicity tour [see AT issue 79]. It was a long world tour that took in just about every major city on the planet and along the way I got to use just about every name-brand PA on the planet. But regardless of what PA I was confronted with, I tuned it to be flat and true, without excessive low, or mid, or high. My goal is to make the sound system exactly reproduce what is coming out of the mixing console. I want to have that control; I want to be able to fine-tune my mix and for those fine tonal and dynamic adjustments to be reproduced as faithfully as possible through the PA.

As I’m writing this, the point I’m making seems obvious – self-evident even: and yet, far too many rock sound systems are overdone in the low-end… often with disastrous consequences.

SUB SYSTEMS: BALANCED RELATIONSHIP

Tuning the main hang of your PA to be as flat as possible is one thing, but the reality of concert touring today is having the PA augmented by a big inventory of subs. And here’s where many engineers get into hot water, especially those taking the leap up from club rigs to stadium or arena systems.

If the subs are in balance with the rest of the PA they’re a great asset – no question. The problem is, they’re all too often overused and end up colouring the whole sound, making the task of mixing on that system very, very difficult, especially for an inexperienced mixer not used to large scale systems in bad rooms.

A MATTER OF LFE & DEATH

The uncomfortable reality is, many large venues around the world have an RT60 in the low frequencies that’s so long it will tend to ‘hold on’ to low notes, and in the case of a kick drum this hold will extend beyond the typical 4/4 timing of most rock music. The result is a complete mess – boomy, unintelligible low-frequency energy that ruins the show experience for the audience.
When setting up the balance between the low frequency elements of the main sound system and the sub-bass systems it’s vital the balance be very carefully matched. The sub-bass systems should only ever be set as an extension of the main system low-end, not as a separate (often louder) entity.

Tune and balance the main system without any of the sub systems turned on. This way the main system can be configured to sound as good as possible with perfect balance between the lows, mids and highs before you introduce the subs. After the subs have been time-aligned to the low end of the main PA, play a favourite track and slowly bring up the subs until they become a true low-end extension (only!) of the existing mains low-end.

Turn the subs off and on a few times to check what they’re actually adding to the low-end and ensure the room is handling all that extra low-end extension. If the room can’t cope with the extra sub energy then adjust it accordingly – downwards! There have been times – in really bad rooms – where I’ve turned the subs off entirely, as they’re doing more harm than good. Once that low-end/sub balance is set correctly, make a note of the levels. This is especially crucial when you’re feeding the subs from a separate mix output. Once you’ve made a note of the levels, stick to that balance for the duration of the show. Later in the night it’ll be nigh-on impossible to get the balance reset correctly if this critical levels relationship gets out of whack.

TUNING: A STEP UP

We’ve determined what excessive low-end can do to a show, but I realise that many reading this article will still be shaking their heads thinking they can’t do without the high-energy impact of some extra power in the subs. And I get that. So try this technique that I call ‘stepped low-end’ tuning.

This technique tunes the PA such that the system is absolutely as flat as possible down to 100Hz (no higher!) and then has a ‘step’ up of approximately 3 – 4dB (no more than that!) from that point down. This eliminates the low-end-into-low-mid overtone that tends to colour the whole system (we’ll delve more into that in a minute) but gives most mixers of rock/pop music the extra punch they need with a tight, solid low-end. Personally, I still tune flat all the way down, and get any extra low-end punch I need out of the channel strip on the console. As a knock-on benefit, I find this also delivers a much better result when I’m recording the gig or feeding it to media or an OB truck.

LOW MIDS: DO THE SUMS

The other area that gets out of control is between the frequencies of 100 and 300Hz. One of the things I teach in my system engineer tuning classes at Clair is that the range between 100 and 300Hz is the critical ‘frequency summation’ area that must be treated very, very carefully when tuning a large-scale system. If you look at a chart of the frequency ranges of most musical instruments – rock or orchestral – in your mix, where do they all overlap? Between 100 and 300Hz. Some don’t go that low, some not that high, but for the overall summation of any set of good mics on most instruments – guitars, keys, drums etc – that’s the area. If that wasn’t tricky enough, guess where most of these arenas and bad rooms sum and interact with the system? That’s right, between 100 and 300Hz!

These two factors really do conspire against us, so in this frequency range we need to be especially careful. Make sure the 100 – 300Hz range is as flat and as tight as possible. In fact, when in doubt I always ‘underdo’ this frequency range (trusting my ears, not Smaart!) because it will inevitably get filled in when I excite the room with my mix. In other words: even if I left the console completely flat, a mix would always have more summation in the 100 – 300Hz area.

TAKE CONTROL

I hope I’ve made a strong case for taking back control of your mix, rather than being a slave to low-end. Still not convinced? Think of it this way: if you tune a system with 4 or 6dB too much low-end energy relative to the mids and highs of a large-scale system, you’ve effectively gone along every single low-frequency EQ section on your mixing console and turned up a full low-frequency shelf 6dB to 8dB! This is before you’ve even started to mix on that console! Always remember: everything you do to the overall system tuning applies to every single channel on the mixing console. The sad reality is that when this happens all those lovely state-of-the-art microphones with their flat response curves have had that response totally ruined and will now have to be ‘hacked up’ with channel EQ to get them to sound vaguely decent.

So before you’ve even started mixing – before you’ve even done a line check – you’re already chasing your tail; trying to compensate for the bass-heavy system tuning. The answer is: don’t! Don’t let the low-end master you. Take control and pull the best mix you’re capable of: the band and the audience will love you for it.